These can be particularly tricky—take note of their positions , and take a photo if you have your phone handy. Any case fans that are plugged directly into the motherboard should now be unplugged as well—they generally go into four-pin plugs around the edges.
You can leave your RAM installed at this point—it will be easier to remove it with the motherboard free. Ditto for any M. If some power or data cables are in the way, you may need to unplug them as well. Now, locate the screws holding the motherboard in place in the case. There are four to eight of them, depending on the size of the motherboard and the case design.
With the retention screws removed, you can grasp the motherboard with both hands and lift it free of the case. If it catches on anything, stay calm, set it down, and remove the obstruction.
When you have the motherboard clear of the case, set it aside. If not, continue on to the next step. This is easy: just press down on the tabs on either side of the RAM, then pull them free of the slot. Now switch to your new motherboard. Re-install your M. Next comes the CPU, so remove the new one from its packaging. It should slide or sit in place with no extra pressure. Lower the plate onto the CPU, and install whatever retention method is used on the socket.
If thermal paste is pre-applied to the bottom of the cooler, just set it down and screw it in place. If not, put a pea-sized amount of thermal paste on the top of the CPU, then lower the cooler on top of it. Install the cooler according to the design and the instructions.
It goes in with simple pressure: just stick the metal rectangle into the open slot in the case. Lower the motherboard down onto the risers, the small metal pieces that accept the retention screws. Now replace the motherboard retention screws. Simply screw them into place, putting them through the holes in the circuit board of the motherboard and down onto the threads in the risers. Now, simply go in reverse for the process that you performed to remove the motherboard. Replace the data and power cables in the same spots.
Check them as you proceed:. Replace the GPU, if you have one. Install it with the reverse process: place it back in the longest PCI-Express slot, press down, and lift the plastic tab to lock it in place. Replace the screw that holds it into the back of the case, and plug in the power rail from the power supply. Now do the same for any other expansion cards you have. Follow the same steps as the external installation above, with any adaptations you may need for its specific design.
Replace the access panel from the case, and screw it into place on the back of the case with its retention screws. You can now move your PC back to its normal position and power it up. Use Google Fonts in Word. Use FaceTime on Android Signal vs. Customize the Taskbar in Windows What Is svchost. Best Smartwatches. Best Gaming Laptops. Best Smart Displays. Best Home Security Systems.
Anyone interested in this esoteric topic is also advised to read this article on ArsTechnica and this related thread. Note the advice on removing non-present devices from device manager.
Let me also note the main area of uncertainty regarding repair installs: it may not be safe with regard to recovering a fully patched system. In principle you can re-apply service packs or hotfixes, but what if Windows Update thinks a hotfix has already been applied when in fact it has been undone?
The Microsoft article above also makes an interesting point about OEM licenses. If you replace the motherboard with something other than the same model, it is considered a new computer and OEM licenses cannot be transferred. MS has a utility called devcon that was originally for XP but works for Vista.
For that matter, properties in devmgmt. INF file somewhere? I think this poses a serious problem for Windows Server an OS I otherwise like very much since it is not at all uncommon to have to reinstall on different hardware and specifically different disk subsystems. I have run SBS at home and at work, and my home machine has had to be rebuilt three times in the lifetime of SBS. Your offline driver file replacement sounds ugly, but if it can be codified, that might be the best we can do.
Also to answer a question about updates and repair installs: Windows will rip out at least some of the updates. Once done, a repaired XP system is practically identical to the original system in stability and functionality.
Thanks David. I do a lot of Dell Motherboard replacements, and have found out that some software will also go out and look for the Asset Tag Number from the Motherboard. If the software cannot verify this number, it can cause the system to reboot or do all sorts of things.
Especially security related network software. It is great information. Some systems get round this with a technique called remapping; but many do not. The problem only occurs if you fit 4GB. Just came across this article and it really helped me a lot. Thanks for your efforts for helping the community. Had to dispose off the board for some reasons and then installed another Asus board with G35 chipset a downgrade from P45 to G The only problem is that after the initial start-up screen with ASUS logo and devices info the system waits too long to get into the OS selection menu.
I am quite clueless at this point what to do in order to get rid of this delay. Any help in this regard will be highly appreciated. I could alternatively have a separate W7 VM, but that would seem redundant as I certainly need the W7 native boot occasionally for processor intensive operations and applications.
It would certainly help if there were a way to effectively reset HAL or the registry so that upon booting it would discover the new devices. Any ideas? Basically in order to get windows7 to recognize the hardware, it has to be in the registry. The only thing is that Windows has to be booted two-three times using the startup repair to switch between native and virtual modes. Thanks for letting us know Wesley. Two or three startup repair boots would defeat the object for me, but I guess it is better than nothing!
Vista no longer supports repair installs. Quick access. Search related threads. Remove From My Forums. Answered by:. Archived Forums. Windows Vista Hardware. Sign in to vote. I suggest backing up your valuable data onto an external drive first. Most modern applications require entering a registration key.
You may have to reenter those keys, so make sure that you have them on hand, preferably on hard copy. If you have a lot of programs, grab Magical Jelly Bean Keyfinder —it will pull all of your registration keys so that you can easily record them. If an application requires activation, it may see a new motherboard as an attempt to copy the software illegally, and it may refuse to run as a result. INF files for newer chipsets. First, check your disk-interface settings.
Migrating between chipsets from different companies can be problematic. Similar considerations hold true for RAID setups , however. There are other possibilities as well—and if you have an unusually complex setup, a clean install may be the only way to go.
For this article, I picked a pretty straightforward project. Though it was already a fairly fast system, it served my purposes, as it consisted of a last-generation CPU running on top of an older chipset.
0コメント